TYM T194 Manual Download

Page: 62 / 169

3 -

OPERATiOn

This manual is an integral part of

the mower.

All operators must read the manual

before operating the mower and

must have access to this manual at

any time.

The purpose of this manual is to

provide information for the safe

and correct use of the mower and

the owner and or any operator of

the mower must read this manual

before operating the machine.

Every effort is made in this manual

and verbally by selling Dealers to

ensure the safe operation of this

mower.
However as the actual operation is

outside the control of Mahindra its

Distributors or their Dealers, no li-

ability of any kind is accepted for

any injury or damage caused by in-

correct operation of this mower.

1. PREFACE

ASSiSTAnCE in USinG THiS

MAnUAL

For any assistance in the use of

this manual or issues not dealt with

in this manual please contact your

selling Dealer.
If additional copies of the manual

are needed they can be purchased

from your selling Dealer.
For copies in a foreign language

please ask your Dealer to make in-

quiry about the availability of a par-

ticular language.

MACHinE USE

This machine is designed solely

for use in customary lawn mowing

operations. Use in any other way

is considered as contrary to the in-

tended use.
The manufacturer accepts no li-

ability for damage or injury resulting

from this misuse, and these risks

must be borne solely by the user.

►

Compliance with and strict adher-

ence to the conditions of operation,

service and repair as specified by the

manufacturer also constitute essen-

tial elements for the intended use.
This machine should be operated,

serviced and repaired only by per-

sons familiar with all its particular

characteristics and acquainted with

the relevant safety rules (accident

prevention). The accident preven-

tion regulations, all other generally

recognized regulations on safety

and occupational medicine and the

road traffic regulations must be ob

served at all times.
Setting fuel delivery beyond pub-

lished factory specifications or oth-

erwise overpowering will result in

loss of warranty protection for this

machine.
Any arbitrary modifications carried

out on this machine will relieve the

manufacturer of all liability for any

resulting damage or injury.

T194(K0) RIDE ON LAWNMOWER-영문-032 2

2018-09-11 오후 5:27:07

Summary of Contents for T194










































































































































































Search results

Summary of Contents for T194

Reviews:

Related manuals for T194

Brands by name

Popular brands

TYM T194, Manual

Search results

Summary of Contents for T194

Reviews:

Related manuals for T194

Brands by name

Popular brands