TYM T194 Manual Download Page 58

Page: 58 / 169

2 - 20

DESCRIPTION OF RIDE ON lawNmOwER CONTROlS

ImPlEmENT lIFT CONTROl

SySTEm

(1) Position lever
This lever is used to lift and lower

an implement to a certain working

height freely and maintain it.

<Operation>

「

Lifting implement

」

Pull the lever back to lift the im-

plement.

「

Lowering implement

」

Push the lever forward to lower

the implement.

►

Position lever

DOWN

When leaving the Ride on lawn-

mower, make sure to lower the

implement and stop the engine.

Others may operate one of the

controls, leading to a dangerous

situation.

•

waRNING

T19O134B

HyDRaUlIC lOwERING

SPEED CONTROl kNOb

This can be used to adjust the low-

ering speed of the implement.
Adjust the lowering speed according

to the implement type and working

environment.

►

Hydraulic lowering

speed control knob

T19O135B

T194(K0) RIDE ON LAWNMOWER-영문-0220 20

2018-07-03 오후 3:49:40

Summary of Contents for T194










































































































































































Search results

Summary of Contents for T194

Reviews:

Brands by name

Popular brands

TYM T194, Manual

Search results

Summary of Contents for T194

Reviews:

Brands by name

Popular brands