TYM T194 Manual Download Page 105

Page: 105 / 169

6 - 5

Maintenance and service

436

(2) changing



Unscrew the drain plug on the

lower section of the engine to

drain contaminated engine oil.

Since hot oil flows out of the en

gine first, be careful not to get

burnt.



After draining oil, tighten the en-
gine oil drain plug.



Add the specified amount of the

specified engine oil through the

filler hole.

4. checking and changing Oil

checking and changing

engine Oil

(1) inspection

①

Pull out the dipstick, wipe its tip

and insert it again. Then, pull it

out and check that the oil level

is between the upper and lower

limits.

②

If insufficient, add oil.

►

T5O508A

Engine oil

gauge

Upper limit

Lower limit

Engine oil

gauge

Engine oil

cartridge

T19O50A

T19O505C

Engine oil

filler

Engine Oil Drain

T194(K0) RIDE ON LAWNMOWER-영문-065 5

2018-08-13 오후 2:30:35

Summary of Contents for T194










































































































































































Search results

Summary of Contents for T194

Reviews:

Related manuals for T194

Brands by name

Popular brands

TYM T194, Manual

Search results

Summary of Contents for T194

Reviews:

Related manuals for T194

Brands by name

Popular brands