TYM T194 Manual Download

Page: 97 / 169

OPERATION

4 -

Observe that every part is properly

operated during driving.

ENgINE OIl PREssuRE

If the engine oil level

warning lamp comes on

during driving, the lubrica

tion system may malfunction. Check

the engine oil immediately and have

your vehicle checked by your work-

shop.

►

ChARgINg

If the battery charge warn

ing lamp comes on dur

ing driving, the battery is

not properly charged. In this case,

check the battery condition, and if

necessary, have it checked by your

workshop.

►

ENgINE COOlANT

If the needle of the coolant gauge

points at "H," stop the engine and

check the followings:

• Radiator coolant

• Radiator fin for clogging

• Fan belt for looseness

If necessary, have your machine

checked by your workshop.

►

11. OPERATION ChECk duRINg dRIvINg

When the coolant temperature

warning lamp comes on, the

engine is overheated. If running

the engine under this condi

tion continuously, the engine

parts can be severely damaged.

Make sure to take an appropri

ate action immediately.

•

NOTE

If driving on a road with an im

plement attached, the front side

of the Ride on lawnmower tends

to be lifted and the vehicle may

not steer properly.

•

wARNINg

(1) When changing the direction on a

road, use the turn signal lamp to in

form other drivers.

(2)

Use the low beam when there is any

vehicle coming on the other side at

nighttime.

(3) Check that the left and right

brake pedals are connected.

(4) Keep the work lamps off when

driving at night.

(5) Follow any applicable laws and

drive safely.

(6) Never let anyone ride the Ride

on lawnmower, except yourself

as a driver.

10. CAuTIONs fOR dRIvINg

ON ROAd

T194(K0) RIDE ON LAWNMOWER-영문-047 7

2018-06-27 오후 6:12:06

Summary of Contents for T194










































































































































































Search results

Summary of Contents for T194

Reviews:

Related manuals for T194

Brands by name

Popular brands

TYM T194, Manual

Search results

Summary of Contents for T194

Reviews:

Related manuals for T194

Brands by name

Popular brands