manualshive.com logo in svg

TYM T194, Manual

Share
Download
TYM T194 Manual Download Page 168

12

 - 1

WARRANTY

1. TYM shall have no obligation or liability under this warranty.

    (1)  for normal maintenance or operation services for Products, including but not  

limited to, providing lubricants, fuel, tune-up inspection or adjustments.

    (2)  for any consumable parts when such parts are replaced as a part of normal maintenance  

or operating services.

    (3)  to any exclusions and limitations contained in the Limited Warranty.
2.   Options, accessories, attachments installed by Dealers which are not manufactured by  

TYM will not be warranted in any way by TYM. For information about the warranty or  
to obtain warranty service on such parts

, 

Dealers should contact the manufacturer directly 

3.  The Limited Warranty is exclusive and in lieu of all other warranties, whether written,  

Oral, express or implied, including any warranty of merchantability or fitness for  
particular purpose.

The liability of TYM under this warranty is expressly limited to the provlsions in the  
Limited Warranty and in no event shall TYM incur any Iiability(including liability 
for general, special, incidental or consequential damages, or economic or moral loss,  
arising out of any failure of the Products) which is not expressly assumed by TYM  
under this warranty.

T194(K0) RIDE ON LAWNMOWER-영문-1214   14

2018-06-28   오전 10:28:24

Summary of Contents for T194










































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands