TYM T194 Manual Download Page 3

Page: 3 / 169

SAFeTY PReCAUTIONS

1. RIDe ON LAWNMOWeR IDeNTIFICATION

The manufacturer warrants this

product and full details of the war-

ranty are provided on a separate

warranty schedule.

WARRANTY OF THe PRODUCT

Service is available from any

TYM

dealer in the country.

To obtain spare parts please contact

your nearest dealer and give him

the details listed below.



Ride on lawnmower model



Ride on lawnmower serial number



Ride on lawnmower engine number



Part number and description



Quantity required

SeRVICe

PARTS

The engine number is stamped on the left hand side of the engine block.
The chassis number is shown on the left hand side of the Ride on lawnmower

as shown in the drawing.

T75O101A

Carved position of the

Engine type or Number

Carved position of the

chassis number

TK0003A

T194(K0) RIDE ON LAWNMOWER-영문-013 3

2018-08-13 오후 4:22:23

Summary of Contents for T194










































































































































































Search results

Summary of Contents for T194

Reviews:

Related manuals for T194

Brands by name

Popular brands

TYM T194, Manual

Search results

Summary of Contents for T194

Reviews:

Related manuals for T194

Brands by name

Popular brands