TYM T194 Manual Download

Page: 53 / 169

2 - 1

DESCRIPTION OF RIDE ON lawNmOwER CONTROlS

Sub Shift Lever

DIFFERENTIal lOCk PED-

The differential lock is a device to

lock the differential system in order

to rotate the left and right wheels at

the same speed. This function can

be used when the rear wheels slip

or one wheel spins.

Engagement - Depressing

pedal

Disengagement - Releasing

pedal

►

Differential lock pedal

When the range shift lever is

placed in the position "H," the

driving speed increased. There-

fore, never put the range shift

lever in the position "H" during

driving backwards.

•

waRNING

Operate the range shift lever only

after the Ride on lawnmower is

completely stopped and with the

brake pedal depressed. Shifting

the lever during driving can dam-

age the gears.

•

NOTE

T19O123A

T19O124A

Never use the differential lock

when driving on a road. A colli-

sion or rollover can occur.
Make sure to release it during

turning. Otherwise, it can lead

to an injury or accident.

•

waRNING

When using the differential lock,

run the engine at a low speed.
If differential lock is still not

disengaged after releasing the

differential lock pedal, gently

depress the left and right brake

pedals alternately.

•

NOTE

T194(K0) RIDE ON LAWNMOWER-영문-0215 15

2018-07-03 오후 3:49:31

Summary of Contents for T194










































































































































































Search results

Summary of Contents for T194

Reviews:

Related manuals for T194

Brands by name

Popular brands

TYM T194, Manual

Search results

Summary of Contents for T194

Reviews:

Related manuals for T194

Brands by name

Popular brands