TYM T194 Manual Download Page 55

Page: 55 / 169

2 - 1

DESCRIPTION OF RIDE ON lawNmOwER CONTROlS

SEaT aND SaFETy bElT

(1) Seat sliding
The seat can be adjusted by moving

it forwards and backwards with the

seat sliding lever on its front pushed

to the left. After adjustment, make

sure that the seat is firmly secured.

►

Seat sliding

Before operating the 4WD lever,

make sure to stop the Ride on

lawnmower.
To avoid damage of transmis-

sion, when front wheel drive

lever is not smoothly shifted,

slightly step forward or rearward

on speed control pedal.
Tires will wear quickly if front

wheel drive is engaged on

paved roads.

•

NOTE

T19O126B

(2) Seat belt

Before driving, adjust the
belt's length to fit to your
body and insert it into its
buckle. When it is engaged
properly, a clicking sound
is heard.

T194(K0) RIDE ON LAWNMOWER-영문-0217 17

2018-07-03 오후 3:49:34

Summary of Contents for T194










































































































































































Search results

Summary of Contents for T194

Reviews:

Brands by name

Popular brands

TYM T194, Manual

Search results

Summary of Contents for T194

Reviews:

Brands by name

Popular brands