manualshive.com logo in svg

TYM T194, Manual

Share
Download
TYM T194 Manual Download Page 20

    - 20

SAFeTY PReCAUTIONS

 

Do not try to change gear go-

ing up or down a steep slope, 

select the correct gear before 

starting.

13. Take care when traveling uphill 

with a heavy implement to en-

sure that it does not overbal-

ance and tip up the front end.

14.  Never  remove  or  modify  the 

seat belt.

15. Never remove, modify or repair 

the ROPS frame.

Please remember that a little bit of 

extra care can prevent serious injury 

or teath and avoid damage to your 

Ride on lawnmower.

▶

THe  FOLLOWING  PReCAU-

TIONS ARe  SUGGeSTeD  TO 

HeLP PReVeNT ACCIDeNTS

A careful operator is the best oper-

ator. Most accidents can be avoid-

ed by observing certain precautions. 

Read and take the following precau-

tions before operating the Ride on 

lawnmower to prevent accidents. 
Ride on lawnmower should be oper-

ated only by those who are respon-

sible and properly trained to do so. 

<THe RIDe ON LAWNMOWeR>

1. Read the operator’s manual care-

fully  before  using  the  Ride  on 

lawnmower.  Lack  of  operating 

knowledge can lead to accidents.

2. Use an approved rollover bar and 

seat belt for safe operation. Over-

turning of a Ride on lawnmower 

without a rollover bar can result 

in death or injury.

3. Do not remove ROPS (Roll Over 

Protective Structure). Always use 

the seat belt.

4. Fiberglass canopy does not give 

any protection.

5. To prevent falls, keep steps and 

platform clear of mud and oil.

6.  Do  not  permit  anyone  but  the 

operator to ride on the Ride on 

lawnmower. There is no safety 

place for extra riders.

7. Replace all missing, illegible or 

damaged safety signs.

8. Keep safety signs clean of dirt 

and grease.

<SeRVICING THe RIDe ON LAWN-

MOWeR>

1. keep the Ride on lawnmower in 

good operating condition for your 

safety. An improperly maintained 

Ride on lawnmower can be haz-

ardous.

2. Stop the engine before perform-

ing any service on the Ride on 

lawnmower.

3. The cooling system operates un-

der pressure, which is controlled 

T194(K0) RIDE ON LAWNMOWER-영문-0120   20

2018-08-13   오후 4:23:19

Summary of Contents for T194










































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands