background image

9 -

Safety Standard for farm work 

76

439

4. cautIonS when drIvIng on the farm road

 

  Driving on roads

   - Drive safely observing the relevant regulation.

   - Drive at safe speed.

   - Be careful not to disturb other drivers.

  - When driving a machine with sharp blade or bump, 

put on a warning sign or detach in advance to pre-

vent any injury.

  - Do not drive fast particularly on winding roads with 

projecting rocks.

  - When driving at night, do not detach lighting device. 

(headlight, turn indicator, work light, brake light, etc)

  - Do not drive fast, abrupt starting, abrupt accelera-

tion, sudden stop, and quick turning. 

  - When driving at high speed, do not slam on the 

brake. Never slam on the brake especially when 

turning at high speed.

 

  When loading/unloading the machine

   - Choose a place with a leveled and safe ground.

   - Drive at low speed.

   - Use a ramp with anti-slippery.

 

  When entering paved road

   - Use a ramp to cross a ditch or a bank.

  - Make sure to use a ramp to enter/exit a high foot-

path Be careful with fall and not to overturn.

  - Check the safety around the surrounding before 

starting to drive.

 

  When driving on a slope

  - Drive at the minimum speed, lower the operating ma-

chine as low as possible and low the center position.

 

T194(K0) RIDE ON LAWNMOWER-영문-095   5

2018-07-03   오후 4:14:43

Summary of Contents for T194










































































































































































Reviews: