TYM T194 Manual Download

Page: 106 / 169

6 - 6

Maintenance and service

Do not add engine oil over the

upper limit level.
Check the engine oil before

starting the engine or at least

in 5 minutes after the engine is

stopped.
When trying to use new oil from

a different manufacturer or oil

with different viscosity, drain

used oil completely before add-

ing new oil.

•

nOte

checking and changing

transMissiOn fluid

(1) inspection

Perform inspection with the engine

stopped.

①

Check the transmission fluid lev

el through the sight glass to see

if the level is between the upper

and lower limits.

②

If insufficient, add oil.

►

If engine oil gets on your skin, it

can irritate the skin and cause

a skin condition. Make sure to

clean your skin with soap and

water or hand cleaner thorough-

ly.
Make sure to cool down the

engine sufficiently before drain

ing oil. Oil is very hot and can

cause a burn if changing oil

right after the engine is stopped.

•

cautiOn

(3) Oil specification

Diesel engine oil:
(API : CD/CF grades 10W/0)

Transmission

fluid filler hole

T19O506A

T194(K0) RIDE ON LAWNMOWER-영문-066 6

2018-08-13 오후 2:30:36

Summary of Contents for T194










































































































































































Search results

Summary of Contents for T194

Reviews:

Related manuals for T194

Brands by name

Popular brands

TYM T194, Manual

Search results

Summary of Contents for T194

Reviews:

Related manuals for T194

Brands by name

Popular brands