TYM T194 Manual Download Page 102

Page: 102 / 169

6 -

Maintenance and service

Opening hOOd

①

Slide the hook to the side. Then,

the hood opens with a clicking

sound.

►

1. Opening cOvers

To prevent any possible failure,

some items should be checked

daily.
Make sure to perform inspection be-

fore driving.

inspectiOn iteMs

Inspect each part in the following

order:

►

2. inspectiOn iteMs

①

Check the items that were

faulty yesterday.

②

Go around the Ride on lawn-

mower and check:

- Lamps for proper illumina-

tion and damage

- Tires for inflation pressure,

crack, damage and wear

- Rotating parts for loose

bolts and nuts

- Transmission fluid level

- Implement attachment sta-

tus

Maintenance and service

T19O501A

Hood lock lever

②

Lift the hood with hands. Then,

the hood is automatically opened

and fixed by its damper.

Hood

T19O50A

T194(K0) RIDE ON LAWNMOWER-영문-062 2

2018-08-13 오후 2:30:22

Summary of Contents for T194










































































































































































Search results

Summary of Contents for T194

Reviews:

Related manuals for T194

Brands by name

Popular brands

TYM T194, Manual

Search results

Summary of Contents for T194

Reviews:

Related manuals for T194

Brands by name

Popular brands