Toshiba e-studio 211c Operator'S Manual Download Page 76

Page: 76 / 225

5-5

Place the original(s).

Page 2-9

Press the EDIT key to enter the editing menu, and

press the BOOK CENTER ERASE key.

- If the key for the desired function is not shown, press the

Next key to switch the screen.

Adjust the width of the book center erase margin,

then press the SET key.

- The default width of the book center erase margin is 10

mm.

- To adjust the width, press the 2mm or 50mm key and

select the desired number.

Select other copy modes as required.

Press the

START key.

3. BOOK CENTER ERASE

This function allows you to erase the shadow in the center of a book original.

Place paper in the drawer(s).

Page 2-4

- When using this mode in bypass copying (

Page 6-5),

be sure to specify the paper size.

Before

After the book center has been erased

Summary of Contents for e-studio 211c


































































































































































































































Search results

Summary of Contents for e-studio 211c

Reviews:

Related manuals for e-studio 211c

Brands by name

Popular brands

Toshiba e-studio 211c, Operator'S Manual

Search results

Summary of Contents for e-studio 211c

Reviews:

Related manuals for e-studio 211c

Brands by name

Popular brands