Toshiba e-studio 211c Operator'S Manual Download Page 52

Page: 52 / 225

3-9

-12-

-13-

-15-

-12-

-13-

-15-

-13-

3. DUPLEX COPYING (1-SIDED, 2-SIDED, BOOK-TYPE)

This function allows you to set the type of originals (1-sided, 2-sided or book-type) and the desired type
of copying (1-sided or 2-sided).

Original

Copy

and

require the optional reversing automatic document feeder to be installed.

and

require the optional automatic duplexer to be installed. In this case, copying can be made

in the thin paper (17~20 lb.) and the plain paper (21~28 lb.) modes only.

*The STACK

symbol flashes on the touch panel when sheets of paper copied on one side are

stacked in the automatic duplexer (optional) during duplex copying; however, this flashing does not
indicate a paper jam.

Summary of Contents for e-studio 211c


































































































































































































































Search results

Summary of Contents for e-studio 211c

Reviews:

Related manuals for e-studio 211c

Brands by name

Popular brands

Toshiba e-studio 211c, Operator'S Manual

Search results

Summary of Contents for e-studio 211c

Reviews:

Related manuals for e-studio 211c

Brands by name

Popular brands