Toshiba e-studio 211c Operator'S Manual Download Page 64

Page: 64 / 225

4-3

Place the original(s).

Page 2-9

Press the COLOR key to enter the color menu.

Then press the HUE/SATURATION key.

Press the HUE key, then the + or - key to adjust

the hue.

- Pressing the + key brings the color closer to the next

clockwise color while pressing the - key brings it closer to
the next counterclockwise color.

2. HUE ADJUSTMENT

This function is available to allow you to adjust the hue by changing the hue circle.

Place paper in the drawer(s).

Page 2-4

Press the START key.

Canceling the Hue Adjustment

There are two ways for clearing the setting.

Press the + or - key on the HUE column to move the

indicator to 0, then press the SET key.

Press the DEFAULT key, then the SET key.

*The saturation setting also becomes the default mode.

Press the SET key.

Select other copy modes as required.

Summary of Contents for e-studio 211c


































































































































































































































Search results

Summary of Contents for e-studio 211c

Reviews:

Related manuals for e-studio 211c

Brands by name

Popular brands

Toshiba e-studio 211c, Operator'S Manual

Search results

Summary of Contents for e-studio 211c

Reviews:

Related manuals for e-studio 211c

Brands by name

Popular brands