Toshiba e-studio 211c Operator'S Manual Download Page 158

Page: 158 / 225

8-21

Set the template name.

- Press the area

as shown on the screen on the

right to switch to the template name input screen.

Enter the template name within 20 letters using the

alphabet (touch panel) and numbers (digital keys),

then press the SET key.

- Use the following keys as required.

...Press these keys to move the cursor.

Backspace

...Press this key to delete a letter before the cursor.

Space

...Press this key to enter a space.

Cancel

...Press this key to cancel entry of letters and

go back to the screen in step 9.

C Clear (control panel)...Press this key to delete all letters.

The setting and registration of the template is

completed.

- If you want to set the other template continuously, press the

NEW key and then perform steps 7 to 11.

Press the SET key.

Summary of Contents for e-studio 211c


































































































































































































































Search results

Summary of Contents for e-studio 211c

Reviews:

Related manuals for e-studio 211c

Brands by name

Popular brands

Toshiba e-studio 211c, Operator'S Manual

Search results

Summary of Contents for e-studio 211c

Reviews:

Related manuals for e-studio 211c

Brands by name

Popular brands