Toshiba e-studio 211c Operator'S Manual Download Page 185

Page: 185 / 225

9-16

WHEN THE GRAPHIC SYMBOLS FLASH ON THE TOUCH PANEL

Pull out the automatic duplexer slowly until it comes

to a stop.

Caution

DO NOT touch the metal portion of a guide plate as it could

burn you.

Push the lever to lift the lower guide plate.

- Make sure that the guide plate is latched to prevent it from

dropping.

Holding the handle of the upper guide plate, lift it

slowly until it comes to a stop. Remove any misfed

paper.

- Be careful not to have the guide plate drop.

Lever

Guide
plate

Remove any misfed paper.

To close the lower guide plate, hold its handle with your right
hand and, lift the lever up to unlatch it with your left hand. Then
put it down slowly.

5. CLEAR PAPER SYMBOL (Cont.)

Guide
plate

Summary of Contents for e-studio 211c


































































































































































































































Search results

Summary of Contents for e-studio 211c

Reviews:

Related manuals for e-studio 211c

Brands by name

Popular brands

Toshiba e-studio 211c, Operator'S Manual

Search results

Summary of Contents for e-studio 211c

Reviews:

Related manuals for e-studio 211c

Brands by name

Popular brands