Toshiba e-studio 211c Operator'S Manual Download Page 31

Page: 31 / 225

2-6

HOW TO MAKE COPIES

The paper size of the drawers of the copier can be changed. The drawers can also be set for THIN,
THICK1 paper or OHP films.
* Bypass copying

Page 6-5

Pull out the drawer toward you.

Push the lever of the side guides in the direction of

the arrow, and set the side guides at the desired pa-

per width (indicated on the bottom surface of the

drawer).

Push the lever in the direction of the arrow, set the

back guide to the desired paper size (indicated on

the bottom surface of the drawer).

Place paper in the drawer.

Page 9-3 (step 2)

2. SETTING COPY PAPER (Cont.)

Changing the Paper Size of the Drawer / Setting the Drawer for Special Uses

Install the drawer into the copier.

Press the PROGRAM key to enter the program

menu. Then press the CASSETTE key.

Adjust the size mark plate to match with the size of

paper that has been set.

Summary of Contents for e-studio 211c


































































































































































































































Search results

Summary of Contents for e-studio 211c

Reviews:

Related manuals for e-studio 211c

Brands by name

Popular brands

Toshiba e-studio 211c, Operator'S Manual

Search results

Summary of Contents for e-studio 211c

Reviews:

Related manuals for e-studio 211c

Brands by name

Popular brands