Toshiba e-studio 211c Operator'S Manual Download Page 79

Page: 79 / 225

USING THE EDITING FUNCTIONS

5-8

Place the original(s).

Page 2-9

Press the EDIT key to enter the editing menu, and

press the FULL IMAGE key.

- The image is automatically reduced by a few percent so

that the entire image can be copied on a sheet.

Select other copy modes as required.

Press the

START key.

5. FULL IMAGE

When the image occupies the entire original (to the edges), use Full Image Copying to reduce the ratio
a little bit so that the edges of the image will not be missed.

Place paper in the drawer(s).

Page 2-4

- When using this mode in bypass copying (

Page 6-5),

be sure to specify the paper size.

Summary of Contents for e-studio 211c


































































































































































































































Search results

Summary of Contents for e-studio 211c

Reviews:

Related manuals for e-studio 211c

Brands by name

Popular brands

Toshiba e-studio 211c, Operator'S Manual

Search results

Summary of Contents for e-studio 211c

Reviews:

Related manuals for e-studio 211c

Brands by name

Popular brands