Toshiba e-studio 211c Operator'S Manual Download Page 162

Page: 162 / 225

8-25

Enter the template name within 20 letters using the

alphabet (touch panel) and numbers (digital keys),

then press the SET key.

- Use the following keys as required.

...Press these keys to move the cursor.

Backspace

...Press this key to delete a letter before the cursor.

Space

...Press this key to enter a space.

Cancel

...Press this key to cancel entry of letters and

go back to the screen in step 9.

C Clear (control panel)...Press this key to delete all letters.

The setting and registration of the template is

completed.

- If you want to set the other template continuously, press the

NEW key and then perform steps 7 to 11.

Press the SET key.

Summary of Contents for e-studio 211c


































































































































































































































Search results

Summary of Contents for e-studio 211c

Reviews:

Related manuals for e-studio 211c

Brands by name

Popular brands

Toshiba e-studio 211c, Operator'S Manual

Search results

Summary of Contents for e-studio 211c

Reviews:

Related manuals for e-studio 211c

Brands by name

Popular brands