Siemens Brodersen MC55 Command Manual Download Page 77

Page: 77 / 475

MC55_ATC_V04.00

Page 77 of 475

3/17/06

Confidential / Released

3.4.7

SIEMENS release cause for L3 Call Control (CC)

3.4.8

SIEMENS release cause for L3 Advice of Charge (AOC)

3.4.9

GSM Release cause for Supplementary Service Call

111

Protocol error, unspecified

Interworking class
127

Interworking, unspecified

Number

Description

Call dropped

Service not available

Hold procedure not available

Temporary no service, previous procedure not yet finished

No speech service available

Call reestablishment procedure active

Mobile received a release (complete) message during a modify procedure (modify reject)

Call clearing, because loss of radio connection, if no reestablishment is allowed (call not

active)

Number not included in FDN list

Notifications
300

Called party barred incoming call

Number

Description

SIM data not available

SIM does not support AOC

SIM data access error

ACM limit almost reached ACM range overflow

ACM range overflow

Number

Description

No error (default)

UnknownSubscriber

IllegalSubscriber

BearerServiceNotProvisioned

TeleserviceNotProvisioned

IllegalEquipment

CallBarred

CUGReject

Number

Description

Summary of Contents for Brodersen MC55




























































































































































































































































































































































































































































































Search results

Summary of Contents for Brodersen MC55

Reviews:

Brands by name

Popular brands

Siemens Brodersen MC55, Command Manual

Search results

Summary of Contents for Brodersen MC55

Reviews:

Brands by name

Popular brands