manualshive.com logo in svg

Siemens Brodersen MC55, Command Manual

Share
Download
Siemens Brodersen MC55 Command Manual Download Page 349

MC55_ATC_V04.00

Page 349 of 475

3/17/06

Confidential / Released

 

 URC 4

<bm>

=2 (PDU mode enabled): 

+CBM: 

<length>

<CR><LF>

<pdu>

Indicates that new cell broadcast message has been received 

 URC 5

<bm>

=2 (text mode enabled): 

+CBM: 

<sn>

, 

<mid>

, 

<dcs>

, 

<page>

, 

<pages>

<CR><LF>

<data>

Indicates that new cell broadcast message has been received 

 URC 6

<ds>

=1 (PDU mode enabled): 

+CDS: 

<length>

<CR><LF>

<pdu>

Indicates that new SMS status report has been received 

 URC 7

<ds>

=1 (text mode enabled): 

+CDS: 

<fo>

, 

<mr>

[, 

<ra>

][, 

<tora>

], 

<scts>

, 

<dt>

, 

<st>

Indicates that new SMS status report has been received 

 URC 8

<ds>

=2: 

+CDSI: 

<mem3>

, 

<index>

Indicates that new SMS status report has been received 

Parameter Description

[0]

(&F)

Buffer unsolicited result codes in the TA. If TA result code buffer is full, indica-

tions can be buffered in some other place or the oldest indications may be dis-

carded and replaced with the new received indications.

1

Discard indication and reject new received message unsolicited result codes

when TA-TE link is reserved (e.g. in on-line data mode). Otherwise forward

them directly to the TE.

2

Buffer unsolicited result codes in the TA when TA-TE link is reserved (e.g. in

on-line data mode) and flush them to the TE after reservation. Otherwise for-

ward them directly to the TE.

3

Forward unsolicited result codes directly to the TE. TA-TE link specific inband

technique used to embed result codes and data when TA is in on-line data

mode. Signaling of unsolicited result codes is configured by 

AT^SCFG

 

Rules for storing received short messages depend on the relevant data coding method (refer to GSM 03.38),

preferred memory storage (

AT+CPMS

) setting and this value.

Note: If AT command interface is acting as the only display device, the ME must support storage of class 0 mes-

sages and messages in the message waiting indication group (discard message) 
[0]

(&F)

No SMS-DELIVER indications are routed to the TE.

1

If SMS-DELIVER is stored in ME/TA, indication of the memory location is

routed to the TE using unsolicited result code: 

<mode>

(num)(&W)

<mt>

(num)(&W)(&V)

Summary of Contents for Brodersen MC55




























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands