manualshive.com logo in svg

Siemens Brodersen MC55, Command Manual

Share
Download
Siemens Brodersen MC55 Command Manual Download Page 336

MC55_ATC_V04.00

Page 336 of 475

3/17/06

Confidential / Released

 

13.3

AT+CMGD Delete short message

The write command deletes a short message from the preferred message storage 

<mem1>

 location 

<index>

. 

Syntax

Notes

• If there is no short message stored at the selected index, the response is OK too. 
• Users should be aware that when using this AT command quickly after SIM PIN authentication the SIM data

may not yet be accessible, resulting in a short delay before the requested AT command response is returned.

See Section 

20.1

, 

Restricted access to SIM data after SIM PIN authentication

 for further detail. 

Test Command

AT+CMGD=?

Response(s)

OK

Write Command

AT+CMGD=

<index>

Response(s)

OK

ERROR

+CMS ERROR

Reference(s)

PIN

ASC0 ASC1

MUX1

MUX2

MUX3 Charge

Last

GSM 07.05

%

%

%

%

%

%

!

!

!

Summary of Contents for Brodersen MC55




























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands