manualshive.com logo in svg

Siemens Brodersen MC55, Command Manual

Share
Download
Siemens Brodersen MC55 Command Manual Download Page 63

MC55_ATC_V04.00

Page 63 of 475

3/17/06

Confidential / Released

 

String values and their 

<indValue>

 ranges.

More indications are available via 

AT^SIND

. Therefore use of 

AT^SIND

 for control of all indications is recom-

mended.

The following indications are accessible via 

AT+CIND

: 

"battchg"

Battery charge level 0..4 or 5 if no measuring is performed, e.g because no bat-

tery is connected. Also refer to 

AT^SBC

. 

"signal"

Signal quality (0..7) or (99) if not measurable 

The indicated value is the bit error rate of the signal received. Bit errors are esti-

mated values. See also 

AT+CSQ

. 

"service"

Service availability (0-1)

0: Not registered to any network

1: Registered to home network or, if "roam"=1 then registered to another net-

work 

"sounder"

Sounder activity (0-1)

Reports every event that causes the ME to generate a tone.

Value 1 means for example:

Incoming call - ME is ringing. Note that the URC "

+CIEV

: sounder" will be out-

put only if ringing tones are activated with 

AT^SRTC

.

Waiting call - ME generates waiting call tone (if call waiting is enabled).

Outgoing call - ME generates Call Progress tone.

Outgoing call - ME generates BUSY tone.

The value changes to 0 when the tone stops. 

"message"

Unread short message at memory location 

<mem1>

 (0-1); refer to 

AT+CPMS

 

"call"

Call in progress (0-1). Indicator value is "1" if at least one call is in state "active"

or "held".

Depending on the parameter 

<succ>

 selected with 

AT^SCFG

 the indicator

"call" will be issued 
• when a state transition ends in state "active" or state "unknown", if

<succ>

="restricted", 

• when any state transition (including transitions beginning or ending in state

"unknown") occurs in the list of active calls or when a traffic channel is

established, if 

<succ>

="verbose". 

Also refer to Section 

7.1

, 

Call Status Information

. 

"roam"

Roaming indicator (0-1)

0: Registered to home network or not registered

1: Registered to other network 

"smsfull"

A short message memory storage in the MT has become full (1) or memory

locations are available (0), i.e. range is (0-1) 

"rssi"

Received signal (field) strength (0..5) or (99) if not measurable 

0: signal strength <= -112 dbm

1-4: signal strength in 15 dbm steps

5: signal strength >= -51 dbm

Received signal (field) strength can also be obtained with 

AT+CSQ

. However,

the signal strength is scaled to value range 0..31 by this command. 

0

Indicator is deregistered. The indicator will not be presented as "

+CIEV

" URC,

but can be queried with 

AT+CIND

?. 

[1]

(&F)(P)

Indicator is registered, indicator event report allowed. 

<indDescr>

(str)

<mode>

(num)

Summary of Contents for Brodersen MC55




























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands