Siemens Brodersen MC55 Command Manual Download Page 133

Page: 133 / 475

MC55_ATC_V04.00

Page 133 of 475

3/17/06

Confidential / Released

7.6

ATD><str> Mobile originated call from active memory using cor-
responding field

Syntax

Command Description

This command searches the active phonebook for a given string

<str>

and dials the assigned phone number.

The termination character ";" is mandatory since dialing from a phonebook is only supported for voice calls and

for sending *# codes of Supplementary Services or other functions.

Parameter Description

String type value ("x"), which should equal an alphanumeric field in at least one phonebook entry in the searched

memories; used character set should be the one selected with

AT+CSCS

<str>

can contain escape sequences

as described in chapter "

Supported character sets

<str>

must be wrapped in quotation marks (""), if escape sequences or parameter

<mgsm>

are used or if the

alphanumeric strings contains a blank. If not, quotation marks are optional.

AT+CSCS

is set to "UCS2", with respect to the coding of UCS2-characters only phonebook entries that contain

an alphanumeric string with as size less than the half of the parameter

from

AT+CPBW

can be

dialed.

String of GSM modifiers:

I Activates CLIR (disables presentation of own phone number to called party)

i Deactivates CLIR (enables presentation of own phone number to called party)

Notes

• This command may be aborted generally by receiving a character during execution. Abortion is not possible

during some states of connection setup such as handshaking.

• The command is not applicable to data calls. Any attempt to dial

<str>

without semicolon ";" causes the

result code "NO CARRIER" to appear.

• Parameter

<mgsm>

only if no *# code is within the dialing string.

Exec Command

ATD>

<str>

[

<mgsm>

];

Response(s)

ERROR

+CME ERROR: <err>

If no dialtone (parameter ATX2 or ATX4):

NO DIALTONE

If busy (parameter setting ATX3 or ATX4):

BUSY

If connection cannot be set up:

NO CARRIER

When TA returns to command mode after call release:

If successfully connected:

Reference(s)

ASC0 ASC1

MUX1

MUX2

MUX3 Charge

Last

V.250

<str>

(str)(+CSCS)

<mgsm>

(str)

Summary of Contents for Brodersen MC55




























































































































































































































































































































































































































































































Search results

Summary of Contents for Brodersen MC55

Reviews:

Brands by name

Popular brands

Siemens Brodersen MC55, Command Manual

Search results

Summary of Contents for Brodersen MC55

Reviews:

Brands by name

Popular brands