manualshive.com logo in svg

Siemens Brodersen MC55, Command Manual

Share
Download
Siemens Brodersen MC55 Command Manual Download Page 237

MC55_ATC_V04.00

Page 237 of 475

3/17/06

Confidential / Released

 

10.4

AT^SISI Internet Service Information

AT^SISI

 serves to monitor the status of Internet service profiles defined with 

AT^SISS

. 

The 

AT^SISI

 read command requests the current status of all defined Internet service profiles. 

The 

AT^SISI

 write command requests the status of the specified Internet service profile. If the specified service

profile is not defined yet, "+CME ERROR" is returned. 

Syntax

Test Command

AT^SISI=?

Response(s)

[

^SISI:

(list of defined 

<srvProfileId>

s)]

OK

Read Command

AT^SISI?

Response(s)

If response is related to service profile(s) created / opened on this interface:
[

^SISI: 

<srvProfileId>

, 

<srvState>

, 

<rxCount>

, 

<txCount>

, 

<ackData>

, 

<unackData>

]

[

^SISI: 

...]

If response is related to service profile(s) created / opened on other interface(s):
[

^SISI: 

<srvProfileId>

, 

<srvParmTag>

value "srvType"]

[

^SISI: 

...]

OK

ERROR

Write Command

AT^SISI=

<srvProfileId>

Response(s)

^SISI: 

<srvProfileId>

, 

<srvState>

, 

<rxCount>

, 

<txCount>

, 

<ackData>

, 

<unackData>

OK

ERROR

+CME ERROR: 

<err>

 

PIN

ASC0 ASC1

MUX1

MUX2

MUX3 Charge

Last

!

%

%

%

%

%

!

!

!

Summary of Contents for Brodersen MC55




























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands