Siemens Brodersen MC55 Command Manual Download Page 418

Page: 418 / 475

MC55_ATC_V04.00

Page 418 of 475

3/17/06

Confidential / Released

17.15

AT^SNFS Select audio hardware set

The

AT^SNFS

write command serves to set the audio mode required for the connected equipment.

AT^SNFS

can also be used in conjunction with

AT^SAIC

. This is useful, for example, if the audio interfaces are

operated alternatively to benefit from different devices. Each audio mode can be assigned a specific interface.

To do so, first select the audio mode with

AT^SNFS

, then activate the audio interface with

AT^SAIC

and finally

enter

AT^SNFW

to store the settings to your audio profile. To switch back and forth it is sufficient to use

AT^SNFS

Syntax

Parameter Description

[1]

Audio mode 1: Standard mode optimized for the reference handset, that can

be connected to the analog interface 1 (see "MC55 Hardware Interface

Description" for information on this handset.) To adjust the volume use the

knob of the reference handset. In audio mode 4, this handset can be used with

user defined parameters.

Note: The default parameters are determined for type approval and are not

adjustable with AT commands.

AT^SNFD

restores

Audio mode 2: Customer specific mode for a basic handsfree (speakerphone)

device (Siemens Car Kit Portable).

Analog interface 2 is assumed as default.

Audio mode 3: Customer specific mode for a mono-headset.

Analog interface 2 is assumed as default.

Audio mode 4: Customer specific mode for a user handset.

Analog interface 1 is assumed as default.

Audio mode 5: Customer specific mode.

Analog interface 1 is assumed as default.

Audio mode 6: Customer specific mode.

Analog interface 2 is assumed as default.

Test Command

AT^SNFS=?

Response(s)

^SNFS:

(list of supported

Read Command

AT^SNFS?

Response(s)

^SNFS:

Write Command

AT^SNFS=

Response(s)

ERROR

CME ERROR: <err>

Reference(s)

ASC0 ASC1

MUX1

MUX2

MUX3 Charge

Last

SIEMENS

(num)(^SNFW)

Summary of Contents for Brodersen MC55




























































































































































































































































































































































































































































































Search results

Summary of Contents for Brodersen MC55

Reviews:

Brands by name

Popular brands

Siemens Brodersen MC55, Command Manual

Search results

Summary of Contents for Brodersen MC55

Reviews:

Brands by name

Popular brands