manualshive.com logo in svg

Siemens Brodersen MC55, Command Manual

Share
Download
Siemens Brodersen MC55 Command Manual Download Page 22

MC55_ATC_V04.00

Page 22 of 475

3/17/06

Confidential / Released

 

1) This code value is reserved for the extension to another extension table. On receipt of this code, a receiving entity shall

display a space until another extension table is defined.

2) This code represents the EURO currency symbol. The code value is the one used for the character 'e'. Therefore a receiv-

ing entity which is incapable of displaying the EURO currency symbol will display the character 'e' instead.

3) This code is defined as a Page Break character and may be used for example in compressed CBS messages. Any mobile

which does not understand the 7 bit default alphabet table extension mechanism will treat this character as Line Feed.

Figure 1.2: 

Extension character table of GSM 03.38 alphabet

Summary of Contents for Brodersen MC55




























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands