manualshive.com logo in svg

Siemens Brodersen MC55, Command Manual

Share
Download
Siemens Brodersen MC55 Command Manual Download Page 405

MC55_ATC_V04.00

Page 405 of 475

3/17/06

Confidential / Released

 

17.6

AT+VTD Tone duration

This command refers to an integer 

<duration>

 that defines the length of tones transmitted with the 

AT+VTS

command. 

Syntax

Parameter Description

Duration of the DTMF signal in 1/10 seconds with tolerance. 

The minimum duration of DTMF signals is 300ms. DTMF tones below 300ms cannot be generated. 
1

(&F)(P)

...255

Test Command

AT+VTD=?

Response(s)

+VTD: 

(list of supported

<duration>

s)

OK

Read Command

AT+VTD?

Response(s)

<duration>

OK

Write Command

AT+VTD=

<duration>

Response(s)

OK

ERROR

+CME ERROR

Reference(s)

PIN

ASC0 ASC1

MUX1

MUX2

MUX3 Charge

Last

GSM 07.07

!

%

%

%

%

%

!

!

!

<duration>

(num)

Summary of Contents for Brodersen MC55




























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands