manualshive.com logo in svg

Siemens Brodersen MC55, Command Manual

Share
Download
Siemens Brodersen MC55 Command Manual Download Page 401

MC55_ATC_V04.00

Page 401 of 475

3/17/06

Confidential / Released

 

17.

Audio Commands

The AT Commands described in this chapter are related to the MC55's audio interface. 

17.1

Audio programming model

The following figure illustrates how the signal path can be adjusted with the parameters 

<inCalibrate>

,

<inBbcGain>

, 

<outBbcGain>

, 

<outCalibrate>

 and 

<sideTone>

 as well as 

<io>

, 

<mic>

 and 

<ep>

. 

Figure 17.1: 

Audio programming model for MC55 Module

Summary of Contents for Brodersen MC55




























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands