manualshive.com logo in svg

Siemens Brodersen MC55, Command Manual

Share
Download
Siemens Brodersen MC55 Command Manual Download Page 413

MC55_ATC_V04.00

Page 413 of 475

3/17/06

Confidential / Released

 

17.12

AT^SNFM Set microphone audio path and power supply

The 

AT^SNFM

 read command returns the microphone mute and supply voltage status.

The 

AT^SNFM

 write command can be used to switch the microphone's audio path (muted / not muted) or to con-

trol the power supply of the MICP2 line (microphone input of the second analog audio interface). 

The microphone can be muted or activated by changing 

<MicSwitch>

 in all audio modes (1 to 6) and during a

voice call only. As an alternative, you can use the 

AT+CMUT

 command to mute the microphone. 

Syntax

Parameter Description

Microphone mute control parameter. 

Evaluated only during voice calls and if 

<MicVccCtl>

 is omitted, e.g. 

AT^SNFM

=1. 

Command does not depend on audio mode. 
0

Mutes the microphone.

1

(P)

Activates the microphone.

Microphone supply voltage control parameter. Setting applies to microphone input 2 only. 

CME error is given if 

<MicSwitch>

 is not omitted. Enter for example 

AT^SNFM

=,1 or 

AT^SNFM

=,2. 

0

Supply voltage is always switched off.

1

Supply voltage is always switched on.

2

(P)

Supply voltage state during voice calls is controlled by the ME. Actual value is

determined by parameter data set of the selected audio mode.

Test Command

AT^SNFM=?

Response(s)

^SNFM: 

(list of supported 

<MicSwitch>

s) , (list of supported 

<MicVccCtl>

s) 

OK

Read Command

AT^SNFM?

Response(s)

^SNFM: 

<MicSwitch>

, 

<MicVccState>

OK

Write Command

AT^SNFM=

[

<MicSwitch>

][, 

<MicVccCtl>

]

Response(s)

OK 

ERROR 

+CME ERROR: 

<err>

 

Reference(s)

PIN

ASC0 ASC1

MUX1

MUX2

MUX3 Charge

Last

SIEMENS

!

%

%

%

%

%

!

!

!

<MicSwitch>

(num)

<MicVccCtl>

(num)

Summary of Contents for Brodersen MC55




























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands