manualshive.com logo in svg

Siemens Brodersen MC55, Command Manual

Share
Download
Siemens Brodersen MC55 Command Manual Download Page 284

MC55_ATC_V04.00

Page 284 of 475

3/17/06

Confidential / Released

 

11.10

AT+CGQREQ Quality of Service Profile (Requested)

Syntax

Command Description

The test command returns values supported as a compound value. If the MT supports several PDP types, the

parameter value ranges for each PDP type are returned on a separate line. 
The read command returns the current settings for each defined context. If no requested profile was explicitly

specified for a context, simply OK will be returned, but default values will be used for that context. 
This command allows the TE to specify a Quality of Service Profile that is used when the MT sends an Activate

PDP Context Request message to the network.

The set command specifies a profile for the context identified by the (local) context identification parameter,

<cid>

.

A special form of the set command, +CGQREQ=

<cid>

 causes the requested profile for context number 

<cid>

to become undefined.

AT&F

 and 

ATZ

 will undefine the QoS profiles of every context which is not active or not online. 

Parameter Description

Parameter specifies a particular PDP context definition. The parameter is local to the TE-MT interface and is

used in other PDP context-related commands. 
1...2

Precedence class
[0]

network subscribed value

1

High Priority

Service commitments shall be maintained ahead of precedence classes 2 and

3

Test Command

AT+CGQREQ=?

Response(s)

+CGQREQ: 

<PDP_type>

, (list of supported 

<precedence>

s), (list of supported 

<delay>

s), (list of 

supported 

<reliability>

s), (list of supported 

<peak>

s), (list of supported 

<mean>

s)

OK

Read Command

AT+CGQREQ?

Response(s)

[

+CGQREQ: 

<cid>

, 

<precedence>

, 

<delay>

, 

<reliability>

, 

<peak>

, 

<mean>

]

[

+CGQREQ: 

...]

Write Command

AT+CGQREQ=

[

<cid>

[, 

<precedence>

[, 

<delay>

[, 

<reliability>

[, 

<peak>

[, 

<mean>

]]]]]]

Response(s)

OK

ERROR

+CME ERROR

Reference(s)

PIN

ASC0 ASC1

MUX1

MUX2

MUX3 Charge

Last

GSM 07.07

%

%

%

%

%

%

!

!

!

<cid>

(num)

<precedence>

(num)

Summary of Contents for Brodersen MC55




























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands