manualshive.com logo in svg

Siemens Brodersen MC55, Command Manual

Share
Download
Siemens Brodersen MC55 Command Manual Download Page 279

MC55_ATC_V04.00

Page 279 of 475

3/17/06

Confidential / Released

 

11.8

AT+CGPADDR Show PDP address

Syntax

Command Description

The test command returns a list of defined 

<cid>

s. 

The write command returns a list of PDP addresses for the specified context identifiers. If no 

<cid>

 is specified,

the addresses for all defined contexts are returned. 

Parameter Description

A numeric parameter which specifies a particular PDP context definition (see 

AT+CGDCONT

 command).

A string that identifies the MT in the address space applicable to the PDP. The address may be static or dynamic.

Note

• If no 

<cid>

 is specified, the write command will return a list of all defined contexts.

Test Command

AT+CGPADDR=?

Response(s)

[

+CGPADDR: 

(list of defined 

<cid>

s)]

OK

Write Command

AT+CGPADDR=

[

<cid>

[,

<cid>

]]

Response(s)

[

+CGPADDR: 

<cid>

, 

<PDP_address>

]

[

+CGPADDR: 

<cid>

, 

<PDP_address>

]

OK

ERROR

+CME ERROR

Reference(s)

PIN

ASC0 ASC1

MUX1

MUX2

MUX3 Charge

Last

GSM 07.07

%

%

%

%

%

%

!

!

!

<cid>

(num)

<PDP_address>

(str)

Summary of Contents for Brodersen MC55




























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands