manualshive.com logo in svg

Siemens Brodersen MC55, Command Manual

Share
Download
Siemens Brodersen MC55 Command Manual Download Page 50

MC55_ATC_V04.00

Page 50 of 475

3/17/06

Confidential / Released

 

2.13

AT^SCFG Extended Configuration Settings

AT^SCFG

 can be used to query and configure various settings of the MC55. 

The 

AT^SCFG

 read command returns a list of all supported parameters and their current values. 

The 

AT^SCFG

 write command queries a configuration parameter (if no value is entered) or sets its value(s). 

Input of parameter names is always coded in GSM character set, parameter values are expected to be given as

specified via 

AT+CSCS

. 

The following error messages may be returned by the 

AT^SCFG

 write commands: 

•

"+CME ERROR: operation temporary not allowed"

 

Change of parameter value(s) temporarily not allowed. 

•

"+CME ERROR: invalid index"

 

Invalid parameter name or value(s). 

•

"+CME ERROR: invalid characters in text string"

 

Character set conversion of parameter value(s) failed. 

•

"+CME ERROR: memory failure"

 

Could not allocate necessary memory or storing a parameter failed. 

•

"+CME ERROR: operation not allowed"

 

Change of parameter value(s) not allowed 

•

"+CME ERROR: unknown"

 

Other error 

Syntax

Test Command

AT^SCFG=?

Response(s)

^SCFG: 

"Audio/AMR", (list of supported 

<amr>

s) 

^SCFG: 

"Call/SpeechVersion1", (list of supported 

<csv1>

s)

^SCFG: 

"GPRS/ATS0/withAttach", (list of supported 

<gs0aa>

s)

^SCFG: 

"GPRS/RingOnIncomingData", (list of supported 

<groid>

s)

^SCFG: 

"PowerSaver/Mode9/Timeout", (list of supported 

<psm9to>

s)

^SCFG: 

"Radio/Band/HandOver", (list of supported 

<HandOverStatus>

s)

^SCFG: 

"Tcp/IRT", (list of supported 

<tcpIrt>

)

^SCFG: 

"Tcp/MR", (list of supported 

<tcpMr>

)

^SCFG: 

"Tcp/OT", (list of supported 

<tcpOt>

)

^SCFG: 

"Tcp/WithURCs", (list of supported 

<tcpWithUrc>

)

^SCFG: 

"URC/CallStatus/CIEV", (list of supported 

<succ>

s)

^SCFG: 

"URC/CallStatus/SLCC", (list of supported 

<sucs>

s)

^SCFG: 

"URC/Datamode/Ringline", (list of supported 

<udri>

s) 

^SCFG: 

"URC/Ringline", (list of supported 

<uri>

s)

^SCFG: 

"URC/Ringline/ActiveTime", (list of supported 

<urat>

s)

OK

Read Command

AT^SCFG?

Response(s)

^SCFG: 

"Audio/AMR", 

<amr>

1

[, 

<amr>

2

[, 

<amr>

3

...[

<amr>

10

]]]

^SCFG: 

"Call/SpeechVersion1", 

<csv1>

^SCFG: 

"GPRS/ATS0/withAttach", 

<gs0aa>

^SCFG: 

"GPRS/RingOnIncomingData", 

<groid>

^SCFG: 

"PowerSaver/Mode9/Timeout", 

<psm9to>

^SCFG: 

"Radio/Band/HandOver", 

<HandOverStatus>

^SCFG: 

"Tcp/IRT", 

<tcpIrt>

^SCFG: 

"Tcp/MR", 

<tcpMr>

^SCFG: 

"Tcp/OT", 

<tcpOt>

Summary of Contents for Brodersen MC55




























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands