manualshive.com logo in svg

Siemens Brodersen MC55, Command Manual

Share
Download
Siemens Brodersen MC55 Command Manual Download Page 188

MC55_ATC_V04.00

Page 188 of 475

3/17/06

Confidential / Released

 

8.14

AT+CPOL Preferred Operator List

The 

AT+CPOL

 read command returns the list of the preferred operators. The 

AT+CPOL

 write command allows to

edit the list of the preferred operators. If 

<index>

 is given but 

<operator>

 is left out, the entry is deleted. An

operator can be only once in the list. 

Syntax

Parameter Description

The order number of the operator in the SIM preferred operator list.

2

Numeric format

Operator in numeric format (GSM Location Area Identification number which consists of a 3-digit country code

plus a 2- or 3-digit network code). 

Test Command

AT+CPOL=?

Response(s)

+CPOL:

(list of supported 

<index>

s), (list of supported 

<format>

s)

OK

ERROR

+CME ERROR

Read Command

AT+CPOL?

Response(s)

+CPOL: 

<index>

, 

<format>

, 

<operator>

+CPOL: 

...

OK

ERROR

+CME ERROR

Write Command

AT+CPOL=

<index>

[, 

<format>

, 

<operator>

]

Response(s)

OK

ERROR

+CME ERROR:

Reference(s)

PIN

ASC0 ASC1

MUX1

MUX2

MUX3 Charge

Last

GSM 07.07

%

%

%

%

%

%

!

!

!

<index>

(num)

<format>

(num)

<operator>

(str)

Summary of Contents for Brodersen MC55




























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands