Siemens Brodersen MC55 Command Manual Download Page 307

Page: 307 / 475

MC55_ATC_V04.00

Page 307 of 475

3/17/06

Confidential / Released

12.5

AT+FCIG Query or set the Local Polling ID

Syntax

Parameter Description

Local Polling ID string, max. length and possible content as reported by test command. Default value is empty

string ("").

Notes

• Used for Fax Class 2 only.
• See also

AT+FLID

Query or set the Local ID setting capabilities.

Test Command

AT+FCIG=?

Response(s)

(max. length of Local Polling ID string) (range of supported ASCII character values)

Read Command

AT+FCIG?

Response(s)

<id>

Write Command

AT+FCIG=

<id>

Response(s)

Reference(s)

ASC0 ASC1

MUX1

MUX2

MUX3 Charge

Last

EIA PN-2388

<id>

(num)

Summary of Contents for Brodersen MC55




























































































































































































































































































































































































































































































Search results

Summary of Contents for Brodersen MC55

Reviews:

Brands by name

Popular brands

Siemens Brodersen MC55, Command Manual

Search results

Summary of Contents for Brodersen MC55

Reviews:

Brands by name

Popular brands