Siemens Brodersen MC55 Command Manual Download Page 132

Page: 132 / 475

MC55_ATC_V04.00

Page 132 of 475

3/17/06

Confidential / Released

7.5

ATD><n> Mobile originated call from active memory using index
number

Syntax

Command Description

TA attempts to set up an outgoing call to the stored number. The termination character ";" is mandatory since

dialing from a phonebook is only supported for voice calls and for sending *# codes of Supplementary Services

or other functions.

Parameter Description

Integer type memory location in the range of locations available in the selected memory, i.e. the index number

returned by

AT+CPBR

String of GSM modifiers:

I Activates CLIR (disables presentation of own phone number to called party)

i Deactivates CLIR (enables presentation of own phone number to called party)

Notes

• This command may be aborted generally by receiving a character during execution. Abortion is not possible

during some states of connection setup such as handshaking.

• The command is not applicable to data calls. Any attempt to dial a data call number from

<n>

causes the

result code "NO CARRIER" to appear.

• Parameter

<mgsm>

only if no *# code is within the dialing string.

Exec Command

ATD>

<n>

[

<mgsm>

];

Response(s)

ERROR

+CME ERROR: <err>

If no dialtone (parameter ATX2 or ATX4):

NO DIALTONE

If busy (parameter setting ATX3 or ATX4):

BUSY

If connection cannot be set up:

NO CARRIER

When TA returns to command mode after call release:

If successfully connected:

Reference(s)

ASC0 ASC1

MUX1

MUX2

MUX3 Charge

Last

V.250

<n>

(num)

<mgsm>

(str)

Summary of Contents for Brodersen MC55




























































































































































































































































































































































































































































































Search results

Summary of Contents for Brodersen MC55

Reviews:

Brands by name

Popular brands

Siemens Brodersen MC55, Command Manual

Search results

Summary of Contents for Brodersen MC55

Reviews:

Brands by name

Popular brands