manualshive.com logo in svg

Siemens Brodersen MC55, Command Manual

Share
Download
Siemens Brodersen MC55 Command Manual Download Page 293

MC55_ATC_V04.00

Page 293 of 475

3/17/06

Confidential / Released

 

11.15

ATA Manual response to a network request for PDP context acti-
vation

The V.250 

ATA

 command may be used to accept a network request for a PDP context activation announced by

the unsolicited result codes "

RING

" or "

+CRING

:  GPRS". The MT responds with CONNECT, enters V.250 online

data state and follows the same procedure as it would after having received a 

AT+CGANS

=1 with no 

<L2P>

 or

<cid>

 values specified. 

If you try to answer a request which is no longer present or which is already answered by another instance, NO

CARRIER is returned. 

Syntax

Exec Command

ATA

Response(s)

CONNECT

NO CARRIER

Reference(s)

PIN

ASC0 ASC1

MUX1

MUX2

MUX3 Charge

Last

GSM 07.07

%

%

%

%

%

%

!

!

%

Summary of Contents for Brodersen MC55




























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands