Home
/
Siemens
/
Brodersen MC55
/
Command Manual

Siemens Brodersen MC55, Command Manual

Share

Page: 71 / 475

Siemens Brodersen MC55 Command Manual Download Page 71

MC55_ATC_V04.00

Page 71 of 475

3/17/06

Confidential / Released

3.4

AT+CEER Extended Error Report

AT+CEER

returns an extended error report regarding the reason of the last

• call release
• failure to set up a call (both mobile originated or terminated)
• failure to modify a call by using Supplementary Services
• failed attempt to activate, register, query, deactivate or deregister a Supplementary Service
• unsuccessful GPRS attach or unsuccessful PDP context activation
• GPRS detach or PDP context deactivation
The release cause report is presented in numeric format. Default output in case of a none-error-situation is

+CEER: 0,0,0. A description associated with each number can be found in the tables given in the following sub-

clauses and the relevant GSM specifications.

The first parameter

<locationID>

serves to locate the other two parameters. Depending on the failure or

release cause either

<reason>

or

<ssRelease>

are applicable, i.e. if

<reason>

≠

0, then

<ssRelease>

= 0.

Vice versa, if

<reason>

= 0, then

<ssRelease>

may be

≠

0.

AT+CEER

is not available for data calls, please use

ATS18

=1 instead. In case of loosed net coverage, MC55 will

disconnect the call but no network release cause is available and the default output will still be given out.

Syntax

Parameter Description

Location ID as number code. Location IDs are listed in Section

3.4.1

,

Cause Location ID for the extended error

report

. Each ID is related with another table that contains a list of

<reason>

s or

<ssRelease>

s.

Reason for last call release as number code. The number codes are listed in several tables, sorted by different

categories in the following subclauses. The tables can be found proceeding from the Location ID given in Sec-

tion

3.4.1

,

Cause Location ID for the extended error report

.

Release cause for last Supplementary Service call (listed in Section

3.4.9

,

GSM Release cause for Supplemen-

tary Service Call

) or last call related use of a Supplementary Service (listed in Section

3.4.10

,

SIEMENS release

cause for Call-related Supplementary Services (CRSS)

).

Test Command

AT+CEER=?

Response(s)

OK

ERROR

+CME ERROR

Exec Command

AT+CEER

Response(s)

+CEER:

<locationID>

,

<reason>

,

<ssRelease>

OK

ERROR

+CME ERROR

Reference(s)

PIN

ASC0 ASC1

MUX1

MUX2

MUX3 Charge

Last

GSM 07.07

%

%

%

%

%

%

!

!

!

<locationID>

(num)

<reason>

(num)

<ssRelease>

(num)

«
...
69
70
71
72
73
...
»

Summary of Contents for Brodersen MC55




























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands