manualshive.com logo in svg

Siemens Brodersen MC55, Command Manual

Share
Download
Siemens Brodersen MC55 Command Manual Download Page 199

MC55_ATC_V04.00

Page 199 of 475

3/17/06

Confidential / Released

 

String type phone number of forwarding address in format specified by 

<type>

. If you select 

<mode>

= 3, the

phone <number> will be registered in the network. This allows you to disable / enable CF to the same destination

without the need to enter the phone number once again. Depending on the services offered by the provider the

registration may be mandatory before CF can be used. The number remains registered in the network until you

register another number or erase it using <mode> = 4.

Type of address octect
145

dialing string 

<number>

 includes international access code character '+'

129

otherwise

Integer or sum of integers each representing a class of information, i.e. a bearer service, telecommunication ser-

vice or bearer service group as defined in "GSM 02.04" 
1

voice

2

data

<class> 2 (data) comprises all those <class> values between 16 and 128, that

are supported both by the network and the MS. This means, a setting made for

<class> 2 applies to all remaining data classes (if supported). In addition, you

can assign a different setting to a specific class. For example, you can activate

Call Forwarding for all data classes, but deactivate it for a specific data class. 

4

fax

8

SMS

16

data circuit sync

32

data circuit async

64

dedicated packet access

128

dedicated PAD access

1...[7]...255

combination of some of the above classes. For example, the default setting 7

represents the sum of the integers 1, 2 and 4 (CF for voice, data and fax). The

value 255 covers all classes. If the <class> parameter is omitted, the default

value 7 is used.

5...[20]...30

Time to wait before call is forwarded, rounded to a multiple of 5 sec. (only for

<reason>

=no reply) 

0

Call Forwarding not active

1

Call Forwarding active

Notes

• You can register, disable, enable and erase 

<reason>

 4 and 5 as described above. However, querying the

status of 

<reason>

 4 and 5 with AT+CCFC will result in an error ("CME error: Operation not supported"). As

an alternative, you may use the ATD command followed by *'# codes to check the status of these two reasons.

See 

Star-Hash (*#) Network Commands

 for a complete list of *# GSM codes. See also examples below. 

• Most networks will not permit registration of new parameters for conditional call forwarding (reasons 1,2,3,5)

while unconditional call forwarding is enabled. 

• The 

AT+CCFC

 command offers a broad range of call forwarding options according to the GSM specifications.

<number>

(str)

<type>

(num)

<class>

(num)

<time>

(num)

<status>

(num)

Summary of Contents for Brodersen MC55




























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands