Siemens Brodersen MC55 Command Manual Download Page 60

Page: 60 / 475

MC55_ATC_V04.00

Page 60 of 475

3/17/06

Confidential / Released

Status Control Commands

The AT Commands described in this chapter allow the external application to obtain various status information

from the MC55.

3.1

AT+CMER Mobile Equipment Event Reporting

This command controls details of the "

+CIEV

" URC presentation related to

AT^SIND

and

AT+CIND

. If registered

via these commands the URCs are sent whenever a value of the related indicator changes.

In addition,

AT+CMER

controls "

^SLCC

" URCs related to

AT^SLCC

. For details refer to

Call Status Infor-

mation

AT^SLCC

and

AT^SCFG

, parameter

<sucs>

The read command returns the URC presentation mode

<mode>

and among others, the indicator event reporting

status

<ind>

The write command enables and disables the presentation of "

+CIEV

<ind-

Value>

]" URCs.

refers to the name of a "

+CIEV

" indicator and

is the new value of

this indicator. After

AT+CMER

has been switched on, URCs for all registered indicators will be issued. See exam-

ples provided in Section

3.2

AT+CIND

and Section

3.3

AT^SIND

Syntax

Unsolicited Result Code

+CIEV:

]

A value of an indicator has changed.

Test Command

AT+CMER=?

Response(s)

+CMER:

(list of supported

<mode>

s), (list of supported

<keyp>

s), (list of supported

<disp>

s), (list of

supported

<ind>

s), (list of supported

<bfr>

Read Command

AT+CMER?

Response(s)

+CMER:

<mode>

<keyp>

<disp>

<ind>

<bfr>

Write Command

AT+CMER=

[

<mode>

<keyp>

<disp>

<ind>

<bfr>

]]]]]

Response(s)

ERROR

+CME ERROR

Reference(s)

ASC0 ASC1

MUX1

MUX2

MUX3 Charge

Last

GSM 07.07

Summary of Contents for Brodersen MC55




























































































































































































































































































































































































































































































Search results

Summary of Contents for Brodersen MC55

Reviews:

Brands by name

Popular brands

Siemens Brodersen MC55, Command Manual

Search results

Summary of Contents for Brodersen MC55

Reviews:

Brands by name

Popular brands