manualshive.com logo in svg

Siemens Brodersen MC55, Command Manual

Share
Download
Siemens Brodersen MC55 Command Manual Download Page 41

MC55_ATC_V04.00

Page 41 of 475

3/17/06

Confidential / Released

 

Any AT command (incl. 

outgoing SMS, voice or 

data call)

Not possible (UART dis-

abled)

Temporary 

Temporary 

Incoming SMS (

AT+CNMI

 

is set to 0,0 (this is the 

default setting)

No effect 

No effect 

No effect 

Incoming SMS (

AT+CNMI

 

is set to 1,1)

Quit 

Quit 

Temporary 

GPRS data transfer

Not possible (UART dis-

abled) 

Temporary

Temporary

RTC alarm line 

Quit 

Quit 

Temporary 

AT+CFUN

=1 

Not possible (UART dis-

abled)

Quit 

Quit 

Event

Selected mode:

<fun>

=0

Selected mode:

<fun>

=5 or 6

Selected mode:

<fun>

=7 or 8 or 9

Summary of Contents for Brodersen MC55




























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands