manualshive.com logo in svg

Siemens Brodersen MC55, Command Manual

Share
Download
Siemens Brodersen MC55 Command Manual Download Page 414

MC55_ATC_V04.00

Page 414 of 475

3/17/06

Confidential / Released

 

Microphone supply voltage control status. 
0

Supply voltage was set to a constant value. 

2

Supply voltage state is controlled by the ME and depends on parameter data

set of the selected audio mode. 

Notes

• The programmable power supply of the MICP2 line gives you greater flexibility in connecting audio accesso-

ries or using MICP2 for a variety of functions other than audio. A detailed description of the extended usage

of MICP2 can be found in 

[8]

. 

• During an active call, users should be aware that when they switch back and forth between different audio

modes (for example handsfree on/off) the value of 

<MicSwitch>

 does not change, i.e. the microphone mode

is retained until explicitly changed. 

<MicVccState>

(num)

Summary of Contents for Brodersen MC55




























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands