manualshive.com logo in svg

Siemens Brodersen MC55, Command Manual

Share
Download
Siemens Brodersen MC55 Command Manual Download Page 288

MC55_ATC_V04.00

Page 288 of 475

3/17/06

Confidential / Released

 

11.11

AT+CGREG GPRS Network Registration Status

AT+CGREG

 write command enables presentation of URC "

+CGREG

: 

<stat>

" when 

<n>

=1 and ME's GPRS net-

work registration status changes. 

AT+CGREG

 read command queries the current URC presentation status and 

<stat>

 which shows whether the

network has currently indicated the registration of the ME. 

Syntax

Unsolicited Result Code

+CGREG: 

<stat>

Indicates a change in the ME's GPRS network registration status. 

Parameter Description

0

(&F)(P)

Disable network registration unsolicited result code

1

Enable network registration URC "

+CGREG

: 

<stat>

" 

0

Not registered, ME is not currently searching an operator to register to. The ME

is in GMM state GMM-NULL or GMM-DEREGISTERED-INITIATED.

GPRS service is disabled, the ME is allowed to attach to GPRS if requested by

the user.

1

Registered, home network. The ME is in GMM state GMM-REGISTERED or

GMM-ROUTING-AREA-UPDATING-INITIATED INITIATED on the home

PLMN

Test Command

AT+CGREG=?

Response(s)

+CGREG: 

(list of supported 

<n>

s)

OK

Read Command

AT+CGREG?

Response(s)

+CGREG: 

<n>

, 

<stat>

OK

Write Command

AT+CGREG=

[

<n>

]

Response(s)

OK

ERROR

+CME ERROR

Reference(s)

PIN

ASC0 ASC1

MUX1

MUX2

MUX3 Charge

Last

GSM 07.07

%

%

%

%

%

%

!

!

!

<n>

(num)

<stat>

(num)

Summary of Contents for Brodersen MC55




























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands