manualshive.com logo in svg

Siemens Brodersen MC55, Command Manual

Share
Download
Siemens Brodersen MC55 Command Manual Download Page 341

MC55_ATC_V04.00

Page 341 of 475

3/17/06

Confidential / Released

 

Notes

• Response if 

AT+CMGR

 is used to read an empty record index: +CMGR: 0,,0 

• Response if 

AT+CMGR

 is used to read a non-existent record index: +CMS ERROR: invalid memory index 

• The parameters 

<ra>

 and 

<tora>

 will only be displayed if parameter 

<ra>

 of the 

AT^SSCONF

 command is

set to 1. 

• Users should be aware that when using this AT command quickly after SIM PIN authentication the SIM data

may not yet be accessible, resulting in a short delay before the requested AT command response is returned.

See Section 

20.1

, 

Restricted access to SIM data after SIM PIN authentication

 for further detail. 

Summary of Contents for Brodersen MC55




























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands