Siemens Brodersen MC55 Command Manual Download Page 346

Page: 346 / 475

MC55_ATC_V04.00

Page 346 of 475

3/17/06

Confidential / Released

13.9

AT+CMSS Send short messages from storage

The write command sends message with location value

<index>

from message storage

<mem2>

to the network

(SMS-SUBMIT or SMS-COMMAND). If new recipient address

<da>

is given for SMS-SUBMIT, it shall be used

instead of the one stored with the message. Reference value

<mr>

is returned to the TE on successful message

delivery. Value can be used to identify message upon unsolicited delivery status report result code.

If the optional parameter

<da>

is given, the old status of the short message at

<index>

remains unchanged

(see

<stat>

Syntax

Test Command

AT+CMSS=?

Response(s)

Write Command

If text mode (

AT+CMGF

=1):

AT+CMSS=

<index>

<da>

<toda>

]]

Response(s)

+CMSS:

<mr>

<scts>

]

If sending fails

ERROR

+CMS ERROR

Write Command

If PDU mode (

AT+CMGF

=0):

AT+CMSS=

<index>

<da>

<toda>

]]

Response(s)

+CMSS:

<mr>

]

If sending fails

ERROR

+CMS ERROR

Reference(s)

ASC0 ASC1

MUX1

MUX2

MUX3 Charge

Last

GSM 07.05

Summary of Contents for Brodersen MC55




























































































































































































































































































































































































































































































Search results

Summary of Contents for Brodersen MC55

Reviews:

Brands by name

Popular brands

Siemens Brodersen MC55, Command Manual

Search results

Summary of Contents for Brodersen MC55

Reviews:

Brands by name

Popular brands