manualshive.com logo in svg

Siemens Brodersen MC55, Command Manual

Share
Download
Siemens Brodersen MC55 Command Manual Download Page 230

MC55_ATC_V04.00

Page 230 of 475

3/17/06

Confidential / Released

 

Syntax

Parameter Description

Internet service profile identifier.

The 

<srvProfileId>

 is used to reference all parameters related to the same service profile. Furthermore,

when using the AT commands 

AT^SISO

, 

AT^SISR

, 

AT^SISW

 and 

AT^SISC

 the 

<srvProfileId>

 is needed

to select a specific service profile. 
0...9

Internet service profile parameter. 
srvType

Type of Internet service to be configured with consecutive usage of 

AT^SISS

. 

For supported values of 

<srvParmValue>

 refer to 

<srvParmValue-srv-

Type>

. 

alphabet

Selects the character set for input and output of string parameters within a pro-

file. 

The selected value is bound to the specific profile. This means that different

profiles may use different alphabets. Unlike other parameters the alphabet can

be changed no matter whether the 

<srvParmTag>

 value "srvType" has been

set. 

For supported values of 

<srvParmValue>

 refer to 

<srvParmValue-

alphabet>

. 

user

User name string 

1.

Socket 

Not applicable. 

2.

FTP 

Not applicable; set within "address" parameter. 

3.

HTTP

Length: 2 ... 31

User name for the HTTP authentication mechanism. Currently only HTTP

simple authentication is supported. 

Test Command

AT^SISS=?

Response(s)

OK

Read Command

AT^SISS?

Response(s)

^SISS: 

<srvProfileId>

, 

<srvParmTag>

, 

<srvParmValue>

OK

Write Command

AT^SISS=

<srvProfileId>

, 

<srvParmTag>

, 

<srvParmValue>

Response(s)

OK 

ERROR 

+CME ERROR: 

<err>

 

PIN

ASC0 ASC1

MUX1

MUX2

MUX3 Charge

Last

!

%

%

%

%

%

!

!

!

<srvProfileId>

(num)

<srvParmTag>

Summary of Contents for Brodersen MC55




























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands