manualshive.com logo in svg

Siemens Brodersen MC55, Command Manual

Share
Download
Siemens Brodersen MC55 Command Manual Download Page 184

MC55_ATC_V04.00

Page 184 of 475

3/17/06

Confidential / Released

 

8.11

AT^SALS Alternate Line Service

The 

AT^SALS

 command is designed to support Alternate Line Service. This allows the subscriber to use two

voice numbers on the same SIM card (service requires a dual line SIM card). 

The write command enables or disables the presentation of 

<view>

 and specifies the 

<line>

 used for outgoing

calls. The read command returns the presentation mode of 

<view>

 and the currently selected 

<line>

. 

Syntax

Unsolicited Result Code

If switched on with 

<view>

=1: 

^SALS: 

<line>

Indicates the line used by an incoming call. 

Parameter Description

Controls the presentation mode of the URC "^SALS" which indicates the line number used by an incoming call: 
0

(&F)(P)

Disables indication of the called line 

1

Enables indication of the called line 

Selects the line to be used for outgoing calls. Setting is global for the ME and non volatile. 
1

(&F)(D)

ALS Line 1 

2

ALS Line 2 

Note

• If a non ALS SIM is inserted, the 

<line>

 will be reset to line 1. 

Test Command

AT^SALS=?

Response(s)

^SALS:

(list of supported 

<view>

s), (list of supported 

<line>

s)

OK

Read Command

AT^SALS?

Response(s)

^SALS: 

<view>

, 

<line>

OK

ERROR

Write Command

AT^SALS=

<view>

[, 

<line>

]

Response(s)

OK

ERROR

Reference(s)

PIN

ASC0 ASC1

MUX1

MUX2

MUX3 Charge

Last

SIEMENS

%

%

%

%

%

%

!

!

!

<view>

(num)

<line>

(num)

Summary of Contents for Brodersen MC55




























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands