manualshive.com logo in svg

Siemens Brodersen MC55, Command Manual

Share
Download
Siemens Brodersen MC55 Command Manual Download Page 311

MC55_ATC_V04.00

Page 311 of 475

3/17/06

Confidential / Released

 

12.9

AT+FDCC Query or set capabilities

This command allows the connected application to sense and constrain the capabilities of the facsimile DCE

(=ME), from the choices defined in CCITT T.30 Table 2. 

Syntax

Notes

• For further information see 

AT+FDIS

. 

• Used for Fax Class 2 only. 

Test Command

AT+FDCC=?

Response(s)

(list of 

<vr>

s), (list of 

<br>

s), (list of 

<wd>

s), (list of 

<ln>

s), (list of 

<df>

s), (list of 

<ec>

s), (list of 

<bf>

s), 

(list of 

<st>

s)

OK

Read Command

AT+FDCC?

Response(s)

<vr>

, 

<br>

, 

<wd>

, 

<ln>

, 

<df>

, 

<ec>

, 

<bf>

, 

<st>

OK

Write Command

AT+FDCC=

<vr>

, 

<br>

, 

<wd>

, 

<ln>

, 

<df>

, 

<ec>

, 

<bf>

, 

<st>

Response(s)

OK

Reference(s)

PIN

ASC0 ASC1

MUX1

MUX2

MUX3 Charge

Last

EIA PN-2388

!

%

!

%

!

!

!

!

!

Summary of Contents for Brodersen MC55




























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands