Siemens Brodersen MC55 Command Manual Download Page 168

Page: 168 / 475

MC55_ATC_V04.00

Page 168 of 475

3/17/06

Confidential / Released

8.4

AT+CREG Network registration

The

AT+CREG

command serves to verify the network registration status of the ME. For this purpose two types of

URCs are available.

The

AT+CREG

read command returns the URC presentation mode

<n>

and an integer

<stat>

that shows the

registration status of the ME. The location information elements

<lac>

and

<ci>

are returned only when

<n>

and ME is registered to the network.

Syntax

Unsolicited Result Codes

URC 1

<n>

=1 and there is a change in the ME network registration status:

+CREG:

<stat>

URC 2

<n>

=2 and there is a change in the ME network registration status or a change of the network cell:

+CREG:

<stat>

<lac>

<ci>

]

Parameter Description

[0]

(&F)

DCREG URC

Enable URC +CREG:

<stat>

to report status of network registration

Enable URC +CREG:

<stat>

<lac>

<ci>

] to report status of network regis-

tration including location information. Optional parameters

<lac>

and

<ci>

will not be displayed during calls or if these values have not changed since last

AT+CREG

read command or since last indication by +CREG URC.

Test Command

AT+CREG=?

Response(s)

+CREG:

(list of supported

<n>

Read Command

AT+CREG?

Response(s)

+CREG:

<n>

<stat>

<lac>

<ci>

]

ERROR

+CME ERROR: <err>

Write Command

AT+CREG=

[

<n>

]

Response(s)

ERROR

+CME ERROR: <err>

Reference(s)

ASC0 ASC1

MUX1

MUX2

MUX3 Charge

Last

GSM 07.07

<n>

(num)(&W)(&V)

Summary of Contents for Brodersen MC55




























































































































































































































































































































































































































































































Search results

Summary of Contents for Brodersen MC55

Reviews:

Brands by name

Popular brands

Siemens Brodersen MC55, Command Manual

Search results

Summary of Contents for Brodersen MC55

Reviews:

Brands by name

Popular brands